The Full Wiki

Tidal power: Map

  
  
  

Wikipedia article:

Map showing all locations mentioned on Wikipedia article:





Tidal power, sometimes called tidal energy, is a form of hydropower that converts the energy of tides into electricity or other useful forms of power.

Although not yet widely used, tidal power has potential for future electricity generation. Tides are more predictable than wind energy and solar power. Historically, tide mills have been used, both in Europe and on the Atlantic coast of North America. The earliest occurrences date from the Middle Ages, or even from Roman times.

Generation of tidal energy

Tidal power is the only form of energy which derives directly from the relative motions of the EarthMoon system, and to a lesser extent from the Earth–Sun system. The tidal forces produced by the Moon and Sun, in combination with Earth's rotation, are responsible for the generation of the tides. Other sources of energy originate directly or indirectly from the Sun, including fossil fuels, conventional hydroelectric, wind, biofuels, wave power and solar. Nuclear is derived using radioactive material from the Earth, geothermal power uses the Earth's internal heat which comes from a combination of residual heat from planetary accretion (about 20%) and heat produced through radioactive decay (80%).

Variation of tides over a day


Tidal energy is generated by the relative motion of the Earth, Sun and the Moon, which interact via gravitational forces. Periodic changes of water levels, and associated tidal currents, are due to the gravitational attraction by the Sun and Moon. The magnitude of the tide at a location is the result of the changing positions of the Moon and Sun relative to the Earth, the effects of Earth rotation, and the local shape of the sea floor and coastlines.

Because the Earth's tides are caused by the tidal forces due to gravitational interaction with the Moon and Sun, and the Earth's rotation, tidal power is practically inexhaustible and classified as a renewable energy source.

A tidal energy generator uses this phenomenon to generate energy. The stronger the tide, either in water level height or tidal current velocities, the greater the potential for tidal energy generation.

Tidal movement causes a continual loss of mechanical energy in the Earth–Moon system due to pumping of water through the natural restrictions around coastlines, and due to viscous dissipation at the seabed and in turbulence. This loss of energy has caused the rotation of the Earth to slow in the 4.5 billion years since formation. During the last 620 million years the period of rotation has increased from 21.9 hours to the 24 hours we see now; in this period the Earth has lost 17% of its rotational energy. While tidal power may take additional energy from the system, increasing the rate of slowdown, the effect would be noticeable over millions of years only, thus being negligible.

Categories of tidal power

Tidal power can be classified into three main types:

  • Tidal stream systems make use of the kinetic energy of moving water to power turbines, in a similar way to windmills that use moving air. This method is gaining in popularity because of the lower cost and lower ecological impact compared to barrage.
  • Barrages make use of the potential energy in the difference in height (or head) between high and low tides. Barrages are essentially dams across the full width of a tidal estuary, and suffer from very high civil infrastructure costs, a worldwide shortage of viable sites, and environmental issues.
  • Tidal lagoons, are similar to barrages, but can be constructed as self contained structures, not fully across an estuary, and are claimed to incur much lower cost and impact overall. Furthermore they can be configured to generate continuously which is not the case with barrages.


Modern advances in turbine technology may eventually see large amounts of power generated from the ocean, especially tidal currents using the tidal stream designs but also from the major thermal current systems such as the Gulf Stream, which is covered by the more general term marine current power. Tidal stream turbines may be arrayed in high-velocity areas where natural tidal current flows are concentrated such as the west and east coasts of Canada, the Strait of Gibraltarmarker, the Bosporusmarker, and numerous sites in Southeast Asia and Australia. Such flows occur almost anywhere where there are entrances to bays and rivers, or between land masses where water currents are concentrated.

Tidal stream generators

A relatively new technology, though first conceived in the 1970s during the oil crisis, tidal stream generators draw energy from currents in much the same way as wind turbines. The higher density of water, 800 times the density of air, means that a single generator can provide significant power at low tidal flow velocities (compared with wind speed). Given that power varies with the density of medium and the cube of velocity, it is simple to see that water speeds of nearly one-tenth of the speed of wind provide the same power for the same size of turbine system. However this limits the application in practice to places where the tide moves at speeds of at least 2 knots (1m/s) even close to neap tides.

Since tidal stream generators are an immature technology (no commercial scale production facilities are yet routinely supplying power), no standard technology has yet emerged as the clear winner, but a large variety of designs are being experimented with, some very close to large scale deployment. Several prototypes have shown promise with many companies making bold claims, some of which are yet to be independently verified, but they have not operated commercially for extended periods to establish performances and rates of return on investments.

Engineering approaches

The European Marine Energy Centremarker categorises them under four heads although a number of other approaches are also being tried.

Axial Turbines

These are close in concept to traditional windmills operating under the sea and have the most prototypes currently operating. These include:

Kvalsundmarker, south of Hammerfestmarker, Norway. Although still a prototype, a turbine with a reported capacity of 300 kW was connected to the grid on 13 November 2003.

A 300 kW Periodflow marine current propeller type turbine — Seaflow — was installed by Marine Current Turbines off the coast of Lynmouthmarker, Devonmarker, England, in 2003. The 11m diameter turbine generator was fitted to a steel pile which was driven into the seabed. As a prototype, it was connected to a dump load, not to the grid.

Since April 2007 Verdant Power has been running a prototype project in the East Rivermarker between Queensmarker and Roosevelt Islandmarker in New York City; it was the first major tidal-power project in the United States. The strong currents pose challenges to the design: the blades of the 2006 and 2007 prototypes broke off, and new reinforced turbines were installed in September 2008.

Following the Seaflow trial, a fullsize prototype, called SeaGenmarker, was installed by Marine Current Turbines in Strangford Loughmarker in Northern Ireland in April 2008. The turbine began to generate at full power of just over 1.2 MW in December 2008 and was reported to have fed 150 kW into the grid for the first time on 17 July 2008. It is currently the only commercial scale device to have been installed anywhere in the world. SeaGen is made up of two axial flow rotors, each of which drive a generator. The turbines are capable of generating electricity on both the ebb and flood tides because the rotor blades can pitch through 180˚.Marine Current Turbines. "Technology." Marine Current Turbines. Marine Current
    Turbines, n.d. Web. 5 Oct. 2009. /www.marineturbines.com/21/
    technology/>.


OpenHydro, an Irish company exploiting the Open-Centre Turbine developed in the U.S., has a prototype being tested at the European Marine Energy Centremarker (EMEC), in Orkney, Scotland.

A prototype semi-submerged floating tethered tidal turbine called Evopodmarker has been tested since June 2008 in Strangford Loughmarker, Northern Irelandmarker at 1/10th scale. The company developing it is called Ocean Flow Energy Ltd, and they are based in the UKmarker. The advanced hull form maintains optimum heading into the tidal stream and it is designed to operate in the peak flow of the water column.

Vertical and horizontal axis crossflow turbines

Invented by Georges Darreius in 1923 and Patented in 1929, these turbines that can be deployed either vertically or horizontally.

The Gorlov turbine is a variant of the Darrieus design featuring a helical design which is being commercially piloted on a large scale in S. Korea, starting with a 1MW plant that started in May 2009 and expanding to 90MW by 2013. Neptune Renewable Energy has developed Proteus which uses a barrage of vertical axis crossflow turbines for use mainly in estuaries.

In late April 2008, Ocean Renewable Power Company, LLC (ORPC) [41109] successfully completed the testing of its proprietary turbine-generator unit (TGU) prototype at ORPC’s Cobscook Baymarker and Western Passage tidal sites near Eastport, Mainemarker. The TGU is the core of the OCGen technology and utilizes advanced design cross-flow (ADCF) turbines to drive a permanent magnet generator located between the turbines and mounted on the same shaft. ORPC has developed TGU designs that can be used for generating power from river, tidal and deep water ocean currents.

Trials in the Strait of Messinamarker, Italy, started in 2001 of the Kobold concept.

Oscillating devices

Oscillating devices do not have a rotating component, instead making use of aerofoil sections which are pushed sideways by the flow. Oscillating stream power extraction was proven with the omni- or bi-directional Wing'd Pump windmill. During 2003 a 150 kW oscillating hydroplane device, the Stingray, was tested off the Scottish coast. The Stingray uses hydrofoils to create oscillation, which allows it to create hydraulic power. This hydraulic power is then used to power a hydraulic motor, which then turns a generator.

Venturi effect

This uses a shroud to increase the flow rate through the turbine. These can be mounted horizontally or vertically.

The Australian company Tidal Energy Pty Ltd undertook successful commercial trials of highly efficient shrouded tidal turbines on the Gold Coast, Queensland in 2002. Tidal Energy has commenced a rollout of their shrouded turbine for a remote Australian community in northern Australia where there are some of the fastest flows ever recorded (11 m/s, 21 knots) – two small turbines will provide 3.5 MW. Another larger 5 meter diameter turbine, capable of 800 kW in 4 m/s of flow, is planned for deployment as a tidal powered desalination showcase near Brisbane Australia in October 2008. Another device, the Hydro Venturi, is to be tested in San Francisco Bay.

Commercial plans

RWE's npower announced that it is in partnership with Marine Current Turbines to build a tidal farm of SeaGen turbines off the coast of Angleseymarker in Wales.

In November 2007, British company Lunar Energy announced that, in conjunction with E.ON, they would be building the world's first tidal energy farm off the coast of Pembrokshire in Wales. It will be the world's first deep-sea tidal-energy farm and will provide electricity for 5,000 homes.Eight underwater turbines, each 25 metres long and 15 metres high, are to be installed on the sea bottom off St David's peninsula. Construction is due to start in the summer of 2008 and the proposed tidal energy turbines, described as "a wind farm under the sea", should be operational by 2010.

British Columbia Tidal Energy Corp. plans to deploy at least three 1.2 MW turbines in the Campbell River or in the surrounding coastline of British Columbia by 2009.

An organisation named Alderney Renewable Energy Ltd is planning to use tidal turbines to extract power from the notoriously strong tidal races around Alderneymarker in the Channel Islands. It is estimated that up to 3GW could be extracted. This would not only supply the island's needs but also leave a considerable surplus for export.

Nova Scotia Power has selected OpenHydro's turbine for a tidal energy demonstration project in the Bay of Fundy, Nova Scotia, Canada and Alderney Renewable Energy Ltd for the supply of tidal turbines in the Channel Islands. Open Hydro

Energy calculations

Various turbine designs have varying efficiencies and therefore varying power output. If the efficiency of the turbine "Cp" is known the equation below can be used to determine the power output.

The energy available from these kinetic systems can be expressed as:

  • P = Cp x 0.5 x ρ x A x V³


where:
Cp = the turbine coefficient of performance
P = the power generated (in watts)
ρ = the density of the water (seawater is 1025 kg/m³)
A = the sweep area of the turbine (in m²)
V³ = the velocity of the flow cubed (i.e. V x V x V)


Relative to an open turbine in free stream, depending on the geometry of the shroud shrouded turbines are capable of as much as 3 to 4 times the power of the same turbine rotor in open flow. .

Potential sites

As with wind power, selection of location is critical for the tidal turbine. Tidal stream systems need to be located in areas with fast currents where natural flows are concentrated between obstructions, for example at the entrances to bays and rivers, around rocky points, headlands, or between islands or other land masses. The following potential sites are under serious consideration:



Barrage tidal power

An artistic impression of a tidal barrage, including embankments, a ship lock and caissons housing a sluice and two turbines.


With only a few operating plants globally, a large 240 MW plant on the Rance Rivermarker, and two small plants, one on the Bay of Fundymarker and the other across a tiny inlet in Kislaya Guba, Russiamarker), and a suggested Severn barrage across the River Severn, from Brean Downmarker in Englandmarker to Lavernock Pointmarker near Cardiffmarker in Walesmarker, the barrage method of extracting tidal energy involves building a barrage across a bay or river, as in the case of the Rance tidal power plantmarker in France. Turbines installed in the barrage wall generate power as water flows in and out of the estuary basin, bay, or river. These systems are similar to a hydro dam that produces Static Head or pressure head (a height of water pressure). When the water level outside of the basin or lagoon changes relative to the water level inside, the turbines are able to produce power. The largest such installationmarker has been working on the Rancemarker river, France, since 1966.

The basic elements of a barrage are caisson, embankments, sluices, turbines, and ship locks. Sluices, turbines, and ship locks are housed in caissons (very large concrete blocks). Embankments seal a basin where it is not sealed by caissons.

The sluice gates applicable to tidal power are the flap gate, vertical rising gate, radial gate, and rising sector.

Barrage systems are affected by problems of high civil infrastructure costs associated with what is in effect a dam being placed across estuarine systems, and the environmental problems associated with changing a large ecosystem.

Potentials for UK barrages are here.

Ebb generation

The basin is filled through the sluices until high tide. Then the sluice gates are closed. (At this stage there may be "Pumping" to raise the level further). The turbine gates are kept closed until the sea level falls to create sufficient head across the barrage, and then are opened so that the turbines generate until the head is again low. Then the sluices are opened, turbines disconnected and the basin is filled again. The cycle repeats itself. Ebb generation (also known as outflow generation) takes its name because generation occurs as the tide changes tidal direction.

Flood generation

The basin is filled through the turbines, which generate at tide flood. This is generally much less efficient than ebb generation, because the volume contained in the upper half of the basin (which is where ebb generation operates) is greater than the volume of the lower half (filled first during flood generation). Therefore the available level difference — important for the turbine power produced — between the basin side and the sea side of the barrage, reduces more quickly than it would in ebb generation. Rivers flowing into the basin may further reduce the energy potential, instead of enhancing it as in ebb generation. Of course this is not a problem with the "lagoon" model, without river inflow.

Pumping

Turbines are able to be powered in reverse by excess energy in the grid to increase the water level in the basin at high tide (for ebb generation). This energy is more than returned during generation, because power output is strongly related to the head. If water is raised 2 ft (61 cm) by pumping on a high tide of 10 ft (3 m), this will have been raised by 12 ft (3.7 m) at low tide. The cost of a 2 ft rise is returned by the benefits of a 12 ft rise. This is since the correlation between the potential energy is not a linear relationship, rather, is related by the square of the tidal height variation.

Two-basin schemes

Another form of energy barrage configuration is that of the dual basin type. With two basins, one is filled at high tide and the other is emptied at low tide. Turbines are placed between the basins. Two-basin schemes offer advantages over normal schemes in that generation time can be adjusted with high flexibility and it is also possible to generate almost continuously. In normal estuarine situations, however, two-basin schemes are very expensive to construct due to the cost of the extra length of barrage. There are some favourable geographies, however, which are well suited to this type of scheme.

Environmental impact

The placement of a barrage into an estuary has a considerable effect on the water inside the basin and on the ecosystem. Many governments have been reluctant in recent times to grant approval for tidal barrages. Through research conducted on tidal plants, it has been found that tidal barrages constructed at the mouths of estuaries pose similar environmental threats as large dams. The construction of large tidal plants alters the flow of saltwater in and out of estuaries, which changes the hydrology and salinity and possibly negatively affects the marine mammals that use the estuaries as their habitatThe La Rance plant, off the Brittany coast of northern France, was the first and largest tidal barrage plant in the world. It is also the only site where a full-scale evaluation of the ecological impact of a tidal power system, operating for 20 years, has been made

French researchers found that the isolation of the estuary during the construction phases of the tidal barrage was detrimental to flora and fauna, however; after ten years, there has been a “variable degree of biological adjustment to the new environmental conditions”

Some species lost their habitat due to La Rance’s construction, but other species colonized the abandoned space, which caused a shift in diversity. Also as a result of the construction, sandbanks disappeared, the beach of St. Servan was badly damaged and high-speed currents have developed near sluices, which are water channels controlled by gates

Turbidity

Turbidity (the amount of matter in suspension in the water) decreases as a result of smaller volume of water being exchanged between the basin and the sea. This lets light from the Sun to penetrate the water further, improving conditions for the phytoplankton. The changes propagate up the food chain, causing a general change in the ecosystem.

Tidal fences and turbines

Tidal fences and turbines can have varying environmental impacts depending on whether or not fences and turbines are constructed with regard to the environment. The main environmental impact of turbines is their impact on fish. If the turbines are moving slowly enough, such as low velocities of 25-50 rpm, fish kill is minimalized and silt and other nutrients are able to flow through the structures For example, a 20 kW tidal turbine prototype built in the St. Lawrence Seaway in 1983 reported no fish kills Tidal fences block off channels, which makes it difficult for fish and wildlife to migrate through those channels. In order to reduce fish kill, fences could be engineered so that the spaces between the caisson wall and the rotor foil are large enough to allow fish to pass through Larger marine mammals such as seals or dolphins can be protected from the turbines by fences or a sonar sensor auto-breaking system that automatically shuts the turbines down when marine mammals are detectedOverall, many researches have argued that while tidal barrages pose environmental threats, tidal fences and tidal turbines, if constructed properly, are likely to be more environmentally benign. Unlike barrages, tidal fences and turbines do not block channels or estuarine mouths, interrupt fish migration or alter hydrology, thus, these options offer energy generating capacity without dire environmental impacts

Salinity

As a result of less water exchange with the sea, the average salinity inside the basin decreases, also affecting the ecosystem. "Tidal Lagoons" do not suffer from this problem.

Sediment movements

Estuaries often have high volume of sediments moving through them, from the rivers to the sea. The introduction of a barrage into an estuary may result in sediment accumulation within the barrage, affecting the ecosystem and also the operation of the barrage.

Fish

Fish may move through sluices safely, but when these are closed, fish will seek out turbines and attempt to swim through them. Also, some fish will be unable to escape the water speed near a turbine and will be sucked through. Even with the most fish-friendly turbine design, fish mortality per pass is approximately 15% (from pressure drop, contact with blades, cavitation, etc.). Alternative passage technologies (fish ladders, fish lifts, fish escalators etc.) have so far failed to solve this problem for tidal barrages, either offering extremely expensive solutions, or ones which are used by a small fraction of fish only. Research in sonic guidance of fish is ongoing.The Open-Centre turbine reduces this problem allowing fish to pass through the open centre of the turbine.

Recently a run of the river type turbine has been developed in France. This is a very large slow rotating Kaplan type turbine mounted on an angle. Testing for fish mortality has indicated fish mortality figures to be less than 5%. This concept also seems very suitable for adaption to marine current/tidal turbines.

Energy calculations

The energy available from a barrage is dependent on the volume of water. The potential energy contained in a volume of water is:
E\, =\, \tfrac12\, A\, \rho\, g\, h^2
where:
  • h is the vertical tidal range,
  • A is the horizontal area of the barrage basin,
  • ρ is the density of water = 1025 kg per cubic meter (seawater varies between 1021 and 1030 kg per cubic meter) and
  • g is the acceleration due to the Earth's gravity = 9.81 meters per second squared.
The factor half is due to the fact, that as the basin flows empty through the turbines, the hydraulic head over the dam reduces. The maximum head is only available at the moment of low water, assuming the high water level is still present in the basin.

Example calculation of tidal power generation

Assumptions:
  • Let us assume that the tidal range of tide at a particular place is 32 feet = 10 m (approx)
  • The surface of the tidal energy harnessing plant is 9 km² (3 km × 3 km)= 3000 m × 3000 m = 9 × 106 m2
  • Density of sea water = 1025.18 kg/m3


Mass of the sea water = volume of sea water × density of sea water
:= (area × tidal range) of water × mass density
:= (9 × 106 m2 × 10 m) × 1025.18 kg/m3
:= 92 × 109 kg (approx)
Potential energy content of the water in the basin at high tide = ½ × area × density × gravitational acceleration × tidal range squared
:= ½ × 9 × 106 m2 × 1025 kg/m3 × 9.81 m/s2 × (10 m)2
:=4.5 × 1012 J (approx)
Now we have 2 high tides and 2 low tides every day. At low tide the potential energy is zero.Therefore the total energy potential per day = Energy for a single high tide × 2
:= 4.5 × 1012 J × 2
:= 9 × 1012 J
Therefore, the mean power generation potential = Energy generation potential / time in 1 day
:= 9 × 1012 J / 86400 s
:= 104 MW
Assuming the power conversion efficiency to be 30%:The daily-average power generated = 104 MW * 30% / 100%
:= 31 MW (approx)


A barrage is best placed in a location with very high-amplitude tides. Suitable locations are found in Russia, USA, Canada, Australia, Korea, the UK. Amplitudes of up to 17 m (56 ft) occur for example in the Bay of Fundymarker, where tidal resonance amplifies the tidal range.

Economics

Tidal barrage power schemes have a high capital cost and a very low running cost. As a result, a tidal power scheme may not produce returns for many years, and investors may be reluctant to participate in such projects.

Governments may be able to finance tidal barrage power, but many are unwilling to do so also due to the lag time before investment return and the high irreversible commitment. For example the energy policy of the United Kingdom recognizes the role of tidal energy and expresses the need for local councils to understand the broader national goals of renewable energy in approving tidal projects. The UK government itself appreciates the technical viability and siting options available, but has failed to provide meaningful incentives to move these goals forward.

Mathematical modeling of tidal schemes

In mathematical modeling of a scheme design, the basin is broken into segments, each maintaining its own set of variables. Time is advanced in steps. Every step, neighbouring segments influence each other and variables are updated.

The simplest type of model is the flat estuary model, in which the whole basin is represented by one segment. The surface of the basin is assumed to be flat, hence the name. This model gives rough results and is used to compare many designs at the start of the design process.

In these models, the basin is broken into large segments (1D), squares (2D) or cubes (3D). The complexity and accuracy increases with dimension.

Mathematical modeling produces quantitative information for a range of parameters, including:
  • Water levels (during operation, construction, extreme conditions, etc.)
  • Currents
  • Waves
  • Power output
  • Turbidity
  • Salinity
  • Sediment movements


Global environmental impact

A tidal power scheme is a long-term source of electricity. A proposal for the Severn Barrage, if built, has been projected to save 18 million tonnes of coal per year of operation. This decreases the output of greenhouse gases into the atmosphere.

If fossil fuel resources decline during the 21st century, as predicted by Hubbert peak theory, tidal power is one of the alternative sources of energy that will need to be developed to satisfy the human demand for energy.

Operating tidal power schemes



Tidal power schemes being considered

In the table, "-" indicates missing information, "?" indicates information which has not been decided









Country Place Mean tidal range (m) Area of basin (km²) Maximum capacity (MW)
United Kingdom and Channel Islands River Severn 7.8 450 8640
Russia Penzhinskaya Baymarker 6.0 20,500 87,000




See also



References

  • Baker, A. C. 1991, Tidal power, Peter Peregrinus Ltd., London.
  • Baker, G. C., Wilson E. M., Miller, H., Gibson, R. A. & Ball, M., 1980. "The Annapolis tidal power pilot project", in Waterpower '79 Proceedings, ed. Anon, U.S. Government Printing Office, Washington, pp 550–559.
  • Hammons, T. J. 1993, "Tidal power", Proceedings of the IEEE, [Online], v81, n3, pp 419–433. Available from: IEEE/IEEE Xplore. [July 26, 2004].
  • Lecomber, R. 1979, "The evaluation of tidal power projects", in Tidal Power and Estuary Management, eds. Severn, R. T., Dineley, D. L. & Hawker, L. E., Henry Ling Ltd., Dorchester, pp 31–39.


Notes

  1. Spain, Rob: "A possible Roman Tide Mill", Paper submitted to the Kent Archaeological Society
  2. George E. Williams. " Geological constraints on the Precambrian history of Earth's rotation and the Moon's orbit". Reviews of Geophysics '38' (2000), 37-60.
  3. Jones, Anthony T., and Adam Westwood. "Power from the oceans: wind energy industries are growing, and as we look for alternative power sources, the growth potential is through the roof. Two industry watchers take a look at generating energy from wind and wave action and the potential to alter." The Futurist 39.1 (2005): 37(5). GALE Expanded Academic ASAP. Web. 8 Oct. 2009.
  4. "Surfing Energy's New Wave" Time International 16 June 2003: 52+. http://www.time.com/time/magazine/article/0,9171,457348,00.html
  5. First power station to harness Moon opens - September 22, 2003 - New Scientist
  6. REUK: "Read about the first open-sea tidal turbine generator off Lynmouth, Devon"
  7. Verdant Power
  8. MIT Technology Review, April 2007 Accessed August 24, 2008]
  9. http://www.marineturbines.com/3/news/
  10. First connection to the grid
  11. · Sea Generation Tidal Turbine
  12. OpenHydro
  13. [1] Ocean Flow Energy Ltd annouce the start of their testing in Strangford Lough
  14. Ocean Flow Energy company website
  15. Gorlov Turbine
  16. Gorlov Turbines in Koreas
  17. Proteus
  18. A.D.A.Group
  19. Wing'd Pump Windmill
  20. Stingray
  21. San Francisco Bay Guardian News
  22. RWE plans 10.5 MW sea current power plant off Welsh coast - Forbes.com
  23. Tidal Power Coming to West Coast of Canada
  24. Alderney Renewable Energy Ltd
  25. http://www.cyberiad.net/library/pdf/bk_tidal_paper25apr06.pdf tidal paper on cyberiad.net
  26. Builder & Engineer - Pembrokeshire tidal barrage moves forward
  27. Severn balancing act
  28. NZ: Chance to turn the tide of power supply | EnergyBulletin.net | Peak Oil News Clearinghouse
  29. Harnessing the power of the sea Energy NZ, Vol 1, No 1, Winter 2007.
  30. Bay of Fundy to get three test turbines | Cleantech.com
  31. Verdant Power
  32. http://deanzaemtp.googlepages.com/PGEbacksnewstudyofbaystidalpower.pdf
  33. Tidal power from Piscataqua River?
  34. http://www.claverton-energy.com/tidal-barrage-potential-in-england.html
  35. Retiere, C. Tidal power and aquatic environment of La Rance.
  36. Charlier, Roger. Forty candles for the Rance River TPP tides provide renewable and sustainable power generation
  37. Pelc, Robin and Fujita, Rob. Renewable energy from the ocean.
  38. VLH TURBINE
  39. §174, p. 260.
  40. [2] (see for example key principles 4 and 6 within Planning Policy Statement 22)
  41. L'Usine marémotrice de la Rance
  42. Nova Scotia Power - Environment - Green Power- Tidal
  43. Race Rocks Demonstration Project
  44. Tidal Energy, Ocean Energy
  45. Information for media inquiries
  46. Korea's first tidal power plant built in Uldolmok, Jindo
  47. http://news.bbc.co.uk/2/hi/uk_news/northern_ireland/7790494.stm
  48. http://www.elektropages.ru/article/4_2006_ELEKTRO.html
  49. Russian power plants soon to utilize tidal energy :: Russia-InfoCentre
  50. http://www.severnestuary.net/sep/pdfs/managingtidalchangeprojectreport-phase1final.pdf
  51. Sihwa Lake Tidal Power Plant targets completion by late 2009
  52. China Endorses 300 MW Ocean Energy Project


External links




Embed code:






Got something to say? Make a comment.
Your name
Your email address
Message